Abit KD7A User Manual Page 1

KD7A Socket 462 System Board User’s Manual 4200-0385-02 Rev. 1.00

6 KD7A Schnellinstallationsanleitung KD7A Schnellinstallationsanleitung Beziehen Sie sich bitte für detaillierte Informationen über diese Hauptplatine

KD7A Schnellinstallationsanleitung 7 Achtung: Vergessen Sie nicht, die korrekte Busfrequenz und -Multiplikator für Ihren Prozessor einzustellen. Ins

8 KD7A Guide d’Installation Rapide KD7A Guide d’Installation Rapide Pour des informations relatives à cette carte mère plus détaillées, veuillez vous

KD7A Guide d’Installation Rapide 9 Attention: N’oubliez pas de programmer la fréquence de bus correcte et le multiple pour votre processeur. Install

10 Краткое руководство по установке KD7A Краткое руководство по установке KD7A Более подробные сведения о материнской плате приведены в руководстве п

Краткое руководство по установке KD7A 11 Внимание: Установите соответствующие частоту и кратность шины процессора. Установка материнской платы в корп

12 Guida all’installazione veloce Scheda madre KD7A Guida all’installazione veloce Scheda madre KD7A Per maggiori e dettagliate informazioni su quest

Guida all’installazione veloce Scheda madre KD7A 13 Installazione della scheda madre sul telaio Dopo avere installato il processore sulla scheda madr

14 14 KD7A KD7A

Introduction 1-1 Chapter 1. Introduction 1-1. Features & Specifications 1. CPU • Supports AMD-K7 Athlon/AthlonXP/Barton Socket A 200/266/333MH

Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of th

1-2 Chapter 1 1-2. Layout Diagram KD7A

Hardware Setup 2-1 Chapter 2. Hardware Setup Before the Installation: Turn off the power supply switch (fully turn off the +5V standby power), or di

2-2 Chapter 2 This motherboard provides a ZIF (Zero Insertion Force) Socket 462 to install AMD Socket A CPU. The CPU you bought should have a kit of

Hardware Setup 2-3 2-3. Install System Memory This motherboard provides 3 184-pin DDR DIMM sites for memory expansion available from minimum 128MB t

2-4 Chapter 2 2-4. Connectors, Headers and Switches Here we will show you all of the connectors, headers and switches, and how to connect them. Plea

Hardware Setup 2-5 (2). FAN Connectors These 3-pin connectors each provide power to the cooling fans installed in your system. The CPU must be kept c

2-6 Chapter 2 (3). CMOS Memory Clearing Header This header uses a jumper cap to clear the CMOS memory. • Pin 1-2 shorted (default): Normal operatio

Hardware Setup 2-7 (5). Wake-up Header These headers use a jumper cap to enable/disable the wake-up function. • PS2-PWR1: Pin 1-2 shorted (default):

2-8 Chapter 2 (6). Front Panel Switches & Indicators Headers This header is used for connecting switches and LED indicators on the chassis front

Hardware Setup 2-9 (7). Additional USB Port Headers This header provides 2 additional USB 2.0 ports connection through an USB cable designed for USB

Table Of Contents KD7A 快速安裝指引 ... 2 KD7A のクイックインストールガイド...

2-10 Chapter 2 (8). Front Panel Audio Connection Header This header provides the connection to audio connector at front panel. • To use the audio c

Hardware Setup 2-11 (9). Internal Audio Connectors These connectors connect to the audio output of internal CD-ROM drive or add-on card. (10).

2-12 Chapter 2 (11). Floppy Disk Drive Connector This connector supports two standard floppy disk drives via a 34-pin 34-conductor ribbon cable. Con

Hardware Setup 2-13 (12). IDE Connectors This motherboard provides two IDE ports to connect up to four IDE drives at Ultra ATA/100 mode by Ultra

2-14 Chapter 2 (13). Back Panel Connectors • Mouse: Connects to PS/2 mouse. • Keyboard: Connects to PS/2 keyboard. • LPT1: Connects to printer o

BIOS Setup 3-1 Chapter 3. BIOS Setup This motherboard provides a programmable EEPROM that you can update the BIOS utility. The BIOS (Basic Input/Out

3-2 Chapter 3 3-1. SoftMenu Setup The SoftMenu utility is ABIT’s exclusive and ultimate solution in programming the CPU operating speed. All the para

BIOS Setup 3-3  Multiplier Factor: This item sets the multiplier factor for the CPU you installed. NOTE: Some processors might have this multiplier

3-4 Chapter 3 3-2. Standard CMOS Features This section contains the basic configuration parameters of the BIOS. These parameters include date, hour,

BIOS Setup 3-5 IDE Primary Master / Slave and IDE Secondary Master / Slave: When set to [Auto], the BIOS will automatically check what kind of IDE dr

3-4. Advanced Chipset Features...3-10 3-5. Integrated Peripherals ...

3-6 Chapter 3 [EGA/VGA]: (Enhanced Graphics Adapter/Video Graphics Array) For EGA, VGA, SVGA and PGA monitor adapters. [CGA 40]: (Color Graphics Adap

BIOS Setup 3-7 3-3. Advanced BIOS Features Hard Disk Boot Priority: This item selects the hard disks booting priority. By pressing <Enter> ke

3-8 Chapter 3 Boot Up NumLock Status: This item determines the default state of the numeric keypad at system booting up. [On]: The numeric keypad fun

BIOS Setup 3-9 Report No FDD For OS: When set to [Enabled], this item allows you to run some older operating system without floppy disk drive. Leave

3-10 Chapter 3 3-4. Advanced Chipset Features DRAM Clock/Drive Control: Click <Enter> key to enter its submenu: Current FSB Frequency: This

BIOS Setup 3-11 DRAM Timing Selectable: Four options are available: Manual  By SPD  Turbo  Ultra. The default setting is By SPD. When set to “By S

3-12 Chapter 3 DDR DQS Input Delay: Two options are available: Auto or Manual. The default setting is Auto. If you set to Manual, then the next item

BIOS Setup 3-13 AGP Fast Write: Two options are available: Disabled  Enabled. The default setting is Disabled. If your AGP adapter can support this

3-14 Chapter 3 PCI Master 0 WS Write: Two options are available: Enabled or Disabled. The default setting is Enabled. When Enabled, writes to the PCI

BIOS Setup 3-15 3-5. Integrated Peripherals OnChip IDE Device: Click <Enter> key to enter its submenu: IDE Prefetch Mode: Two options are ava

1 User’s Manual

3-16 Chapter 3 [Mode 0-4]: You can select a mode that matches your disk drive’s timing. Do not use the wrong setting or you will have drive errors. 

BIOS Setup 3-17  USB Mouse Support Via: This item allows you to select [BIOS] for using USB mouse in DOS environment, or [OS] in OS environment. 

3-18 Chapter 3 [PCI Slot]: When the system boots, it will first initialize PCI. Onboard FDD Controller: Two options are available: Enabled and Disabl

BIOS Setup 3-19 3-6. Power Management Setup ACPI Suspend Type: This item selects the type of Suspend mode. [S1(PowerOn Suspend)]: Enables the Power

3-20 Chapter 3 [Last State]: When power returns after an AC power failure, the system will return to the state where you left off before power failur

BIOS Setup 3-21 Resume by OnChip USB: Two options are available: Disabled or Enabled. The default setting is Disabled. When set to Enabled, any event

3-22 Chapter 3 IRQ Activity Monitroing: Click <Enter> key to enter its submenu: All Interrupt Event: Two items available: Off or Manual. The d

BIOS Setup 3-23 3-7. PnP/PCI Configurations Force Update ESCD: If you want to clear ESCD data next time you boot up, and ask the BIOS to reset the s

3-24 Chapter 3  Back to PnP/PCI Configurations Setup Menu: PCI/VGA Palette Snoop: This item determines whether the MPEG ISA/VESA VGA cards can work

BIOS Setup 3-25 3-8. PC Health Status CPU Shutdown Temperature: This item sets the temperature that would shutdown the system automatically in orde

2 KD7A 快速安裝指引 KD7A 快速安裝指引 如您要瞭解此主機板更詳細的資訊，請參閱我們的完整版使用手冊，裡面會有詳盡的說明。此快速安裝手冊是給有經驗的系統組裝者使用，如果這是您第一次嘗試來組裝您的電腦系統，我們建議您先去閱讀完整版的使用手冊，或是詢問技術人員來幫助您組裝您的電腦系統。（完整

3-26 Chapter 3 All Voltages, Fans Speed and Thermal Monitoring: These unchangeable items list the current status of the CPU and environment temperatu

Install VIA 4-in-1 Driver A-1 Appendix A. Install VIA 4-in-1 Driver NOTE: Please install this VIA 4-in-1 driver first after having installed the Win

A-2 Appendix A Click [Next]. 6. 7. Choose [Yes, I want to restart my computer now.], and click [OK] to complete setup. KD7A

Install Audio Driver B-1 Appendix B. Install Audio Driver The installation procedures and screen shots in this section are based on Windows 2000 op

B-2 Appendix B B-2 Appendix B KD7A KD7A

Install LAN Driver C-1 Appendix C. Install LAN Driver The installation procedures and screen shots in this section are based on Windows 2000 operat

C-2 Appendix C C-2 Appendix C KD7A KD7A

Install VIA USB 2.0 Driver D-1 Appendix D. Install VIA USB 2.0 Driver NOTE: There is no need to install VIA USB 2.0 driver for the Windows XP operat

D-2 Appendix D Click [Yes]. 6. Click [OK]. 7. Click [Print to File]. 8. Click [OK]. 9. KD7A

BIOS Update Guide E-1 Appendix E. BIOS Update Guide The procedure illustrated here is based on the model SE6 as an example; all other models follow

KD7A 快速安裝指引 3 將主機板安裝到機殼上 當您將處理器安裝到主機板上之後，您便可以開始將主機板固定到電腦機殼裡去。首先；請您先將主機板固定到電腦機殼。大多數的電腦機殼底座都有許多的固定孔位，請將主機板上的固定孔位與機殼底座上的固定孔位對準。如果孔能對準並且有螺絲孔，就表示可使用銅柱來固定主

E-2 Appendix E 6. Please set the first boot sequence as “Floppy” in BIOS and boot off the floppy disk. 7. Flash the BIOS in pure DOS mode. A:\&g

Hardware Monitoring (The Winbond Hardware Doctor Utility) F-1 Appendix F. Hardware Monitoring (The Winbond Hardware Doctor Utility) The Winbond Hard

F-2 Appendix F 6. Execute the Hardware Doctor by entering the Windows Menu [Start]  [Programs]  [Winbond]  [Hardware Doctor]. 7. This screen a

Troubleshooting (Need Assistance?) G-1 Appendix G. Troubleshooting (Need Assistance?) Q & A: Q: Do I need to clear the CMOS before I use a new

G-2 Appendix G Q: How can I get a quick response to my request for technical support? A: Be sure to follow the guidelines as stated in the “Technic

Troubleshooting (Need Assistance?) G-3 Main instructions: To fill in this “Technical Support Form”, refer to the step-by-step instructions given belo

G-4 Appendix G  Technical Support Form  Company Name:  Phone Number:  Contact Person:  Fax Number:  E-mail Address: Model * BIOS ID #

How to Get Technical Support H-1 Appendix H. How to Get Technical Support (From our website) http://www.abit.com.tw (In North America) http://www.ab

H-2 Appendix H 4. Internet Newsgroups. They are a great source of information and many people there can offer help. ABIT's Internet News group,

How to Get Technical Support H-3 North America and South America: ABIT Computer (U.S.A.) Corporation 45531 Northport Loop West, Fremont, California

4 KD7A のクイックインストールガイド KD7A のクイックインストールガイド このマザーボードの詳細については、ユーザーズマニュアルの完全版を参照してください。このクイックインストールガイドは、経験あるシステム構築者向けに書かれました。今回始めてコンピュータシステムをセットアップする方は、まず

H-4 Appendix H 7. RMA Service. If your system has been working but it just stopped, but you have not installed any new software or hardware recently,

KD7A のクイックインストールガイド 5 注意：正しいバス周波数と倍数をプロセッサ用に設定するのを忘れないでください。 マザーボードをシャーシに取り付ける マザーボードにプロセッサを取り付けた後、シャーシにマザーボードを固定することができるようになります。まず、シャーシにマザーボードを固定する必要